266 lines
10 KiB
Markdown
266 lines
10 KiB
Markdown
|
|
|
|
nmrpflash - Netgear Unbrick Utility
|
|
====================================
|
|
|
|
`nmrpflash` uses Netgear's [NMRP protocol](http://www.chubb.wattle.id.au/PeterChubb/nmrp.html)
|
|
to flash a new firmware image to a compatible device. It has been successfully used with the
|
|
Netgear D7000, DNG3700v2, EX2700, EX6100v2, EX6120, EX6150v2, EX8000, R6020, R6080, R6100, R6220, R6400, R7000, R7000P
|
|
R6800, R8000, R8000P, R8500, WNDR3800, WNDR4300, WNDR4500v3 WNR3500, but is likely to be compatible with
|
|
many other Netgear devices as well.
|
|
|
|
Prebuilt binaries for Linux, macOS and Windows are available [here](https://github.com/jclehner/nmrpflash/releases)
|
|
([Npcap](https://nmap.org/npcap/#download) is required on Windows). On Linux and macOS, you can also use
|
|
[Homebrew](https://formulae.brew.sh/formula/nmrpflash). FreeBSD packages can be fetched and installed using the FreeBSD `pkg` command.
|
|
|
|
```
|
|
Usage: nmrpflash [OPTIONS...]
|
|
|
|
Options (-i, and -f or -c are mandatory):
|
|
-a <ipaddr> IP address to assign to target device [10.164.183.253]
|
|
-A <ipaddr> IP address to assign to selected interface [10.164.183.252]
|
|
-B Blind mode (don't wait for response packets)
|
|
-c <command> Command to run before (or instead of) TFTP upload
|
|
-f <firmware> Firmware file
|
|
-F <filename> Remote filename to use during TFTP upload
|
|
-i <interface> Network interface directly connected to device
|
|
-m <mac> MAC address of target device (xx:xx:xx:xx:xx:xx)
|
|
-M <netmask> Subnet mask to assign to target device [255.255.255.0]
|
|
-t <timeout> Timeout (in milliseconds) for NMRP packets [10000 ms]
|
|
-T <timeout> Time (seconds) to wait after successfull TFTP upload [1800 s]
|
|
-p <port> Port to use for TFTP upload [69]
|
|
-R <region> Set device region (NA, WW, GR, PR, RU, BZ, IN, KO, JP)
|
|
-S <n> Skip <n> bytes of the firmware file
|
|
-v Be verbose
|
|
-V Print version and exit
|
|
-L List network interfaces
|
|
-h Show this screen
|
|
```
|
|
|
|
### Using nmrpflash
|
|
|
|
Download the correct firmware image for your device. When downloading from the Netgear site,
|
|
the firmware is usually contained in a `.zip` file - extract this first. The actual firmware
|
|
file will have an extension such as `.chk`, `.bin`, `.trx` or `.img`.
|
|
|
|
Now, using an Ethernet cable, connect your Netgear router to the computer that will run
|
|
`nmrpflash`. Use the LAN port, which is often colored blue on Netgear devices. If the
|
|
router has multiple LAN ports, use the one labled `1`.
|
|
|
|
Next, you'll have to determine which network interface corresponds to the one connected to
|
|
the Netgear router. All available interfaces can be listed using
|
|
|
|
```
|
|
# nmrpflash -L
|
|
eth0 192.168.1.2 c0:de:fa:ce:01:23
|
|
eth2 0.0.0.0 ca:fe:ba:be:45:67
|
|
wifi0 10.0.10.138 de:ad:be:ef:89:ab
|
|
```
|
|
|
|
For the rest of this example, let's assume that your router is connected to `eth2`, and that
|
|
you want to flash a firmware image named `EX2700-V1.0.1.8.img`.
|
|
|
|
First of all, turn *off* the router. Then start `nmrpflash` using the following command:
|
|
|
|
```
|
|
# nmrpflash -i eth2 -f EX2700-V1.0.1.8.img
|
|
Waiting for Ethernet connection (Ctrl-C to skip).
|
|
```
|
|
|
|
As soon as you see the `Waiting for Ethernet connection.` message, turn the router *on*. If all went
|
|
well, `nmrpflash` will continue printing messages:
|
|
|
|
```
|
|
Advertising NMRP server on eth2 ... /
|
|
Received configuration request from fe:ed:1b:ad:f0:0d
|
|
Sending configuration: 10.164.183.252/24
|
|
Received upload request: filename 'firmware'.
|
|
Uploading EX2700-V1.0.1.8.img ... OK (3539077 b)
|
|
Waiting for remote to respond.
|
|
Received keep-alive request (11).
|
|
Remote finished. Closing connection.
|
|
Reboot your device now.
|
|
```
|
|
|
|
Now reboot the device, and you're good to go.
|
|
|
|
### Common issues
|
|
|
|
**In any case, run `nmrpflash` with `-vvv` before filing a bug report!**
|
|
|
|
###### "Error while loading shared libraries: ..." (Linux)
|
|
|
|
You must install your Linux distribution's `libpcap` and `libnl-3`
|
|
packages (exact names will vary depending on your distribution).
|
|
|
|
On Debian based distros (such as Ubuntu) you can install these dependencies with
|
|
|
|
sudo apt install libpcap libnl-3
|
|
|
|
###### "The program can't start because wpcap.dll is missing" (Windows)
|
|
|
|
Install [Npcap](https://nmap.org/npcap/). For `nmrpflash` versions prior
|
|
to 0.9.14, install Npcap with "WinPcap Compatibility" enabled.
|
|
|
|
Version 0.9.13 was the last version to support Windows XP.
|
|
|
|
###### "nmrpflash cannot be opened because the developer cannot be verified." (macOS)
|
|
|
|
Go to ` -> System Preferences -> Security & Privacy`. Under the `General` tab, there should
|
|
be a message like "nmrpflash was blocked from use because it is not from an identified
|
|
developer". Click the `Allow anyway` button next to it, and run `nmrpflash` again.
|
|
If that doesn't work, try [this](https://support.apple.com/guide/mac-help/open-a-mac-app-from-an-unidentified-developer-mh40616/mac).
|
|
|
|
Please note that [Homebrew](https://formulae.brew.sh/formula/nmrpflash) is the preferred method of
|
|
installing `nmrpflash` on macOS.
|
|
|
|
###### "No suitable network interfaces found."
|
|
|
|
Make sure the network interface is up (wireless interfaces are not supported).
|
|
On Windows, try restarting the Npcap service (commands must be run as
|
|
administrator):
|
|
|
|
```
|
|
C:\> net stop npf
|
|
C:\> net start npf
|
|
```
|
|
|
|
###### "No response after 60 seconds. Bailing out."
|
|
|
|
**Always run `nmrpflash` in the sequence described above!**
|
|
|
|
You can try specifying the MAC address using `-m xx:xx:xx:xx:xx:xx`,
|
|
or, if that still doesn't work, "blind mode" using `-B`. Note that
|
|
careful timing between running `nmrpflash` and turning on the router may
|
|
be required in this mode.
|
|
|
|
It's also possible the bootloader itself is bricked, or that the
|
|
particular device does not support the NMRP protocol.
|
|
|
|
###### "Timeout while waiting for ACK(0)/OACK."
|
|
|
|
The device did not respond to `nmrpflash`'s TFTP upload request. By default,
|
|
`nmrpflash` will assign `10.164.183.252` to the target device, while adding `10.164.183.253`
|
|
to the network interface specified by the `-i` flag. You can use `-a` to change the IP
|
|
address assigned to the target (e.g. if your network is `192.168.1.0/24`, specify a *free*
|
|
IP address, such as `-a 192.168.1.252`), and `-A` to change the IP address used for the
|
|
network interface.
|
|
|
|
###### "Timeout while waiting for CLOSE_REQ."
|
|
|
|
After a successful file upload, `nmrpflash` waits for up to 15 minutes for an
|
|
answer from your device. You can increase this by specifying a longer timeout
|
|
using `-T` switch (argument is in seconds).
|
|
|
|
It's entirely possible that the image was flashed successfully, but the
|
|
operation took longer than 15 minutes.
|
|
|
|
###### "Address X/Y cannot be used on interface Z."
|
|
|
|
`nmrpflash` refuses to use an IP address / subnet mask combination that would
|
|
make the remote device unreachable from the device running `nmrpflash`. For
|
|
example, if the IP address of your computer is 192.168.0.1/255.255.255.0, assigning
|
|
192.168.2.1/255.255.255.0 to the router makes no sense, because the TFTP upload will
|
|
fail.
|
|
|
|
###### "IP address of X has changed. Please assign a static IP to the interface."
|
|
|
|
This can happen if the network interface in question automatically detects that
|
|
the network cable has been connected, and your computer tries to reconfigure that
|
|
interface (NetworkManager on Linux does this for example) - this can usually be
|
|
disabled.
|
|
|
|
###### "Received keep-alive request."
|
|
|
|
This usually means that flashing is in progress. On some devices, you may get a few
|
|
hundred keep-alive requests before it eventually finishes!
|
|
|
|
###### "TFTP block rollover. Upload might fail!"
|
|
|
|
By default, file transfers using TFTP are limited to `65535 * 512` bytes
|
|
(almost 32 MiB). Uploading files exceeding this limit might fail, depending
|
|
on the device. If it does fail, your only option is flashing an older image,
|
|
which is smaller than 32 MiB.
|
|
|
|
###### "Ignoring extra upload request."
|
|
|
|
Extraneous upload requests are usually sent by the device if the image validation
|
|
failed. Some possible causes are:
|
|
|
|
* If you downloaded a firmware that's contained in an archive (a `.zip` for
|
|
example), you must extract this file, and then use the contained firmware file
|
|
as the argument to the `-f` parameter. Some examples for file extensions used
|
|
for firmware: `.chk`, `.bin`, `.trx`, `.img`.
|
|
|
|
* Some devices prevent you from downgrading the firmware. See if it works with
|
|
the latest version available for your device. If you're already using the latest
|
|
version, it might be possible to patch the version info of the firmware file. A
|
|
future version of `nmrpflash` might incorporate an auto-patch feature for these
|
|
cases.
|
|
|
|
* Your device might expect a different image format for `nmrpflash` than when
|
|
flashing via the web interface.
|
|
|
|
###### "Timeout while waiting for 0000." after "Waiting for remote to respond."
|
|
|
|
This could indicate that the device hasn't finished flashing, after the default timeout
|
|
(15 minutes). Try increasing the timeout, using the `-T <seconds>` option,
|
|
for example use `-T 1800` to specify a timeout of 30 minutes.
|
|
|
|
###### "bind: Cannot assign requested address"
|
|
|
|
Specify the address of the router (`-a`), and address of your computer (`-A`).
|
|
For example:
|
|
|
|
`-A 10.0.0.2 -a 10.0.0.1`
|
|
|
|
or
|
|
|
|
`-A 192.168.1.2 -a 192.168.1.1`
|
|
|
|
### Building and installing
|
|
###### Linux, Mac OS X, BSDs
|
|
|
|
On Linux, developer packages for `libpcap`, `libnl` and `libnl-route` must be installed:
|
|
|
|
```
|
|
$ sudo apt install libpcap-dev libnl-3-dev libnl-route-3-dev
|
|
```
|
|
|
|
Then, it's as easy as
|
|
|
|
```
|
|
$ make && sudo make install
|
|
```
|
|
|
|
On Linux and macOS, you can use [Homebrew](https://brew.sh) to install `nmrpflash`:
|
|
|
|
```
|
|
$ brew install nmrpflash
|
|
```
|
|
|
|
On FreeBSD (assuming the ports infrastructure is installed and you have root permissions):
|
|
|
|
```
|
|
$ cd /usr/ports/sysutils/nmrpflash
|
|
$ make install
|
|
```
|
|
|
|
Or install the FreeBSD binary package with:
|
|
|
|
```
|
|
$ pkg install nmrpflash
|
|
```
|
|
|
|
###### Windows
|
|
|
|
The repository includes a [CodeBlocks](https://www.codeblocks.org/) project
|
|
file (`nmrpflash.cbp`). Download the latest [Npcap SDK](https://nmap.org/npcap/)
|
|
and extract it into the a folder named `Npcap` in the source's root directory.
|
|
|
|
### Donate
|
|
|
|
You can [buy me a coffee](https://www.buymeacoffee.com/jclehner) if you want, but please consider
|
|
donating the money for charity instead - [Médecins Sans Frontiers](https://www.msf.org/donate) comes to mind,
|
|
but any other organization, local or international, that you think deserves support will do. Thank you!
|
|
|